HP 410C DRIVER DOWNLOAD

We were unable to find any drivers for your product. The Modei C can be operated from either or volts, 50 to cps. Remove probe tip from Model A and connect the ac probe as shown in Figure We retain the right to refuse any refund if we feel the return policy is being abused. All Hewlett-Packard instruments are equipped with a three-conductor power cable which grounds the instrument when plugged into an appropri- Connect Model C ac probe to voltmeter calibrator output terminals. To avoid surface contamination of the printed circuit, clean with weak solution of warm water and mild detergent after repair.

Uploader:	Grolrajas
Date Added:	16 December 2015
File Size:	44.44 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	10147
Price:	Free* [*Free Regsitration Required]

HP Photosmart Premium Fax e-All-in-One Printer series - C410

Javascript is disabled in this browser. If meter does not function properly, refer to Paragraph for adjustment procedure. It can be rack mounted only. The Model C is a submodular unit designed for bench use. Please note that our shop is not responsible for customs or any fee.

Vacuum Tube Voltmeter C Equipment Hewlett-Packard, HP;

Adjust dc power supply for System voltmeter readings listed in Table If it does not, adjust A6R20 for 1. DC voltage, DC current and resistance knobs and indicators are in black; AC voltage controls and indicators are in red.

Connect the Model C as shown in Figure Solder one terminal of the button capacitor to the measurement point in the circuit and not to the probe contact. Manufacturer refurbished An item that has been professionally restored to working order by a manufacturer or manufacturer-approved vendor. All hhp inputs are located on the front panel; a DC output connector is located on the rear panel.

As the photoconductors are alternately illuminated by the neona, their respective resistances are low conductive when illuminated and high non-conductive when darkened. Modulator - Demodulator Mechanical Analogy. Place instrument in original container if available.

Warranty New A brand-new, unused, unopened, undamaged item in its original packaging where packaging is applicable. Equipment having similar characteristics may be substituted for items listed.

Conduct a visual check of the Model C for possible burned or loose components, loose connecmight tions, or any other obvious conditions which suggest a source of trouble.

Allow at least a 20 Vary test oscillator frequency from 20 cps to 10 Mc. Instructions for installing the Model C are 140c in Figure Would you like to view the product details page for the new product?

HP Customer Support - Software and Driver Downloads

The DC voltage developed across these shunt resistors, when applied through the modulator-amplifier-demodulator network to the meter, provide a deflection on the meter proportional to the DC current being measured.

Test Equipment Required To avoid leakage, an additional capacitor with a dielectric such as mylar or polystyrene which has high resistance to leakage is required. Owning to the resonant rise in the probe circuit at frequencies above megacycles, the meter may be more sensitive to the harmonics than to the 410f. Replace 10 ohm resistor with 10 M ohm resistor. Any warranty support needed would be completed by the third party that sold the product. Model C should read approximately ma.

Performance Checks Change i TM Page Section 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 - 7 9 1 1 1 1 2 2 2 2 2 3 3 3 3 3 3 4 4. Stack the submodular units in the frame as shown instep 2, Figure 410d make dependable measurements hl these frequencies, the circuits being measured must be free of ail parasitics.

HP Photosmart Premium Fax e-All-in-One Printer - Cc - Driver Downloads | HP® Customer Support

You can find anything in our shop from cameras and engines, military surplus, rf equipment, test equipment, computer parts, electronic parts and more! A portion of the meter circuit voltage is fed back to the modulator. Connect Model C ac probe to voltmeter calibrator output terminals.